AMS 5604 17-4PH Stainless Steel Sheet & Strip: Mastering Formability and Heat TreatmentCore Advantage: ZYTC Alloy supplies aerospace-grade AMS 5604 17-4PH (UNS S17400) stainless steel sheet, strip, and plate (up to 4.0"thickness). Sourced from vacuum-melted heats and supplied in the soft Condition A state, our sheet is specifically engineered to overcome the most common fabrication challenges—minimizing springback during forming and ensuring a predictable aging response (H900-H1150) with zero heat-treatment distortion. |  |
The Sheet Metal Challenge: Forming 17-4PHWhile17-4PH is renowned for its 190 ksi yield strength after aging, fabricating it into aircraft skins, structural brackets, or complex sheet metal components presents unique challenges. The key is to perform all major forming operations in the Condition A (Solution Annealed) state. In this condition, the material is relatively soft (approx. 30-35 HRC) and highly ductile. Springback Control: Like all high-strength alloys, 17-4PH exhibits significant springback during cold forming. Because it is supplied in Condition A, you can bend and stamp it, but die compensation and over-bending are required. Post-Forming Aging: Once formed, the component is aged at temperatures between 482°C (H900) and 621°C (H1150). Because aging is a simple low-temperature precipitation process with no quenching, the formed part will not distort or warp, maintaining its precise dimensional tolerances.
ZYTC Engineering Tip: If you are experiencing edge cracking during deep drawing, verify that your incoming strip has been properly solution-annealed. Our in-house lab checks the grain size of the strip to ensure it has the optimal ductility for your stamping process.
Welding Considerations for 17-4PH Thin GaugeWelding 17-4PH sheet is common (used for exhaust components and airframe hardware), but doing it without sacrificing joint strength requires strict process control: Filler Metal: Use matching 17-4PH filler wire (e.g., AMS 5825) or ER630. Pre-heat & Interpass Temperature: For thin gauge sheet, pre-heating is generally not required, but the interpass temperature should be maintained between 100°C - 150°C. The"Soft Zone"Issue: Welding in the Condition A state leaves a soft, unaged heat-affected zone (HAZ). The entire welded assembly must be aged after welding to restore full strength across the joint. Post-Weld Aging: Solution treatment is generally not required after welding if the joint is aged directly. However, if maximum corrosion resistance and toughness are required, a full re-solution anneal (Condition A) followed by aging is recommended.
Quality Verification at ZYTC (Our In-House Lab)For aerospace sheet metal, a mill certificate is not enough. The microstructure and precise chemistry dictate how the sheet will perform in your press brake or welding cell. ZYTC verifies every batch: Metallurgical Microscope: We inspect the sheet's microstructure for δ-ferrite content and inclusion cleanliness. A controlled ferrite content is critical to ensure predictable formability and prevent cracking during stamping. Direct Reading Spectrometer: We strictly verify that the Copper (Cu) and Niobium (Nb) content are within the precise ranges required by AMS 5604. This ensures your aging process (H900, etc.) will yield the exact hardness and strength you designed for. Universal Testing Machine: We test the mechanical properties (Tensile & Yield) of the actual sheet thickness, not just the ingot, guaranteeing the rolling process did not degrade the material.
  
Technical Specifications & Availability| Parameter | Specification |
|---|
| Material | 17-4PH / UNS S17400 / ASTM A693 | | Standard | AMS 5604 (Aerospace Grade) | | Condition | Solution Heat Treated (Condition A) | | Thickness Range | Sheet/Strip: 0.25 mm – 4.75 mm (0.010"– 0.187") Plate: 4.8 mm – 102 mm (0.188"– 4.0") | | Width Range | Up to 1219 mm (48") - Custom slitting available | | Certification | ISO 9001 & AS 9120B, EN 10204 3.1 MTC |
|  |
ApplicationsOur AMS 5604 sheet and strip are primarily used in: Aerospace: Aircraft skins, structural brackets, fasteners, and engine components. Chemical Processing: Thin-wall pressure vessels, heat exchangers, and ducting. Oil & Gas: Downhole tool housings and wellhead components (H1150 condition for sour service).
Request a QuoteWhether you need a prototype sheet for forming trials or a full production coil, ZYTC provides competitive factory-direct pricing and certified materials. To request a quote, please provide: Thickness and Width required. Quantity (kg or sheets). Required condition (Condition A or Aged H900/H1025/H1150). Application details (to help us advise on formability).
📧Email: daisy@zytcsteel.com 📱WhatsApp/WeChat: +86 17335753350 |