UNS N07093 / Alloy 93 / GH4093 - ZYTC Alloy
MODEL NO: Alloy 93 / UNS N07093 (GH4093)
UNS N07093 / Alloy 93 / GH4093 High-Strength Wrought Nickel-Base Superalloy (Gamma-Prime Strengthened) for Aero-Engine Blades, Discs and Fasteners — Service to 815 °C Wrought Ni-Base | γ′ Precipitation Strengthened | VIM + VAR / ESR Melted | UK Aero Heritage |
| UNS N07093 | Density 8.19 g/cm³ | Max service ~815 °C | Melting 1360–1390 °C | China grade GH4093 |
ZYTC Alloy is an ISO 9001 & AS 9120B certified manufacturerofNimonic® 93 (UNS N07093 / GH4093), a wrought Ni-Co-Cr gamma-prime strengthened superalloywithhigher cobalt and chromium content, offering high strength and excellent structural stability at temperatures up to 815 °C. Supplied as bar, plate/sheet, forgings and rings with full heat treatment and per-heat traceability. Request a free quote and technical data today.
I. Product Information
| Item | Description |
|---|---|
| Material Name | Alloy 93 Wrought Nickel-Base Superalloy (UNS N07093, China grade GH4093 / GH93, original trade name Nimonic® 93) |
| Material Definition | A precipitation-hardenable nickel-base superalloy containing relatively high cobalt (15.0–21.0 %) and chromium (18.0–21.0 %), strengthened by gamma-prime (γ′) phase. Higher strength and better structural stability than earlier Nimonic® grades; designed for service below 815 °C. |
| Core Value Proposition | A proven wrought alloy for hot-stressed rotating and fastener hardware: good hot-workability (upset deformation up to 80 % without cracking at 1050–1150 °C), stable long-term microstructure, and UK aero-engine service heritage. |
| Key Advantages | γ′ precipitation strengthening | High strength at 650–815 °C | Excellent structural stability under long-term aging | Good hot-workability and forgeability | UK / French aero-engine heritage |
| Product Forms | Bar & Rod | Plate & Sheet | Forgings & Rings | Machined-to-drawing parts |
II. Material Standards & Specifications
| Standard / Designation | Scope |
|---|---|
| UNS N07093 | Unified Numbering System (USA), wrought nickel-base superalloy |
| GB/T 14992 — GH4093 / GH93 | China high-temperature alloy designation system |
| UK BS HR series (historical) | British aerospace material specifications (original home of the Nimonic® family) |
| EN 10204 3.1 | Mill test certificate with every lot (3.2 third-party inspection on request) |
Important clarification on specifications: No AMS specification exists for this alloy. Some commercial websites wrongly cite AMS 5708 (in fact Waspaloy®, UNS N07001, forging stock), AMS 5898 (a premium bearing stainless steel), AMS 5899 (a PM tool steel, UNS S44004), AMS 5860 (Custom 455®, UNS S45500) or AMS 5829 (Nimonic® 80A/90 bar) as Alloy 93 specifications — all are misattributions. Composition and properties are verified against UNS N07093 / GH4093 and the mill certificate; aerospace parts are supplied to purchaser / OEM drawing requirements.
III. Chemical Composition (wt%)
| Element | Min | Max |
|---|---|---|
| Nickel (Ni) | Balance | – |
| Chromium (Cr) | 18.0 | 21.0 |
| Cobalt (Co) | 15.0 | 21.0 |
| Titanium (Ti) | 2.0 | 3.0 |
| Aluminum (Al) | 1.0 | 2.0 |
| Carbon (C) | – | 0.13 |
| Iron (Fe) | – | 1.00 |
| Manganese (Mn) | – | 1.00 |
| Silicon (Si) | – | 1.00 |
| Phosphorus (P) | – | 0.015 |
| Sulfur (S) | – | 0.015 |
| Copper (Cu) | – | 0.20 |
| Boron (B) | – | 0.02 (calculated addition) |
| Lead (Pb) | – | 0.0025 |
IV. Physical & Mechanical Properties
| Physical Property | Typical Value |
|---|---|
| Density | 8.19 g/cm³ |
| Melting Range | 1360–1390 °C |
| Maximum Service Temperature | ~815 °C (creep / stress loaded) |
Condition: solution treated 1050–1080 °C / 8 h / air cool, then aged 710 ± 10 °C / 16 h / air cool.
| Temperature | Tensile Strength | 0.2% Yield Strength | Elongation |
|---|---|---|---|
| Room Temperature | ≥ 1080 MPa | ≥ 685 MPa | ≥ 20 % |
| 815 °C (1490 °F) | ≥ 588 MPa | ≥ 294 MPa | ≥ 30 % |
Values are typical specified minimums for wrought bar / forging per Chinese handbook data. Certified test report values per lot govern.
V. Typical Applications
Aero Engines Turbine blades, small-engine turbine discs and rotors, hot-section fasteners |
Industrial & Marine Gas Turbines Free-turbine blades and discs, hot-stressed rotor hardware |
High-Temperature Fasteners Bolts, shims, lock plates and washers for 650–815 °C service |
MRO & Legacy Repair Spares and repair parts for UK / French legacy engine hardware |
Selection Boundaries — when NOT to choose Alloy 93:
- Maximum strength below ~700 °C with easier fabrication: consider Alloy 718
- Creep-loaded parts above 850–920 °C: consider Nimonic® 90orWaspaloy®
- Severe aqueous / chemical corrosion: consider Alloy 625orHastelloy® C-276
VI. Manufacturing Process & Heat Treatment
| Process | Parameters | Outcome |
|---|---|---|
| Solution Anneal | 1050–1080 °C, 8 h, air cool | Dissolves γ′, recrystallizes, prepares for aging |
| Aging | 710 ± 10 °C, 16 h, air cool | γ′ precipitation, peak strength & stability |
| Melting Route | VIM + VAR or VIM + ESR (double / triple melt) | High cleanliness, low gas and trace-element content |
- Hot Working: forge / upset at 1050–1150 °C (start 1130–1150 °C, finish ≥ 950 °C); upset deformation up to 80 % without cracking.
- Welding: GTAW (argon-arc) in the solution-treated condition; stress-relieve and re-age after welding.
- Machining: best machinability in the solution-treated state; use rigid setups, sharp carbide tooling and positive feeds.
VII. Material Comparison Guide
| Dimension | Alloy 93 | Nimonic® 90 | Waspaloy® | Alloy 718 |
|---|---|---|---|---|
| Strengthening | γ′ (Ni3(Al,Ti)) | γ′ | γ′ + carbides | γ′′ |
| Max Service Temp. | ~815 °C | ~920 °C | ~870 °C | ~704 °C |
| High-Co Content | 15–21 % | 15–21 % | 12–15 % | ≤ 1 % |
| Typical Use | Blades, discs, fasteners to 815 °C | Blades, discs to 920 °C | Turbine discs, shafts, seals | Discs, casings, oil & gas |
| Designations | UNS N07093 / GH4093 | UNS N07090 / GH4090 | UNS N07001 / AMS 5706/5708 | UNS N07718 / AMS 5662/5663 |
Procurement recommendation:ChooseAlloy 93 for wrought blade / disc / fastener hardware in the 650–815 °C band with proven UK aero heritage; choose Nimonic® 90orWaspaloy® when higher creep temperatures are required; choose Alloy 718 for maximum economy and strength below ~700 °C.
VIII. Supply & Quality Control
- Forms:bar / rod, plate & sheet, forgings & rings, machined-to-drawing parts
- Minimum order: 50 kg | Supply ability: 5000 kg / month | Stock lead time: 7–10 days | Delivery: FOB | Origin: CHINA
- EN 10204 3.1 mill test certificate with every lot; 3.2 third-party inspection on request
- Per-heat traceability, in-house laboratory verification; ISO 9001 & AS 9120B certified
Request a Quote or Sample Today Send your drawing or specification — our technical team will confirm feasibility, quote and delivery. Email: daisy@zytcsteel.com | WhatsApp / WeChat: +86 17335753350 |








