+86-17335753350

Model No: Inconel 740H

UNS N07740 / Inconel 740H / 2.4663 Bar — Precipitation-Hardenable Nickel Superalloy for A-USC Power

ZYTC Alloy 740H (UNS N07740) — Precipitation-Hardenable Nickel-Cobalt-Chromium Superalloy. As an ISO 9001 and AS 9120B certified supplier, ZYTC Alloy presents this technical guide for Inconel 740H for confident material evaluation.
Quantity :
Contact Now

I. Product Information

  • Material Name: Inconel 740H Nickel-Chromium-Cobalt Superalloy (UNS N07740 / W.Nr. 2.4663)
  • Material Definition: A precipitation-hardenable Ni-Cr-Co superalloy strengthened by gamma-prime (γ′) phase, developed specifically for advanced ultra-supercritical (A-USC) steam service at 700–800 °C.
  • Core Value Proposition: The only nickel alloy code-qualified for A-USC boiler construction under ASME Code Case 2702, with a maximum use temperature of 800 °C (1472 °F) and 100,000-hour creep-rupture strength at 750 °C / 35 MPa.
  • Key Advantages: Gamma-prime (γ′) strengthening | Excellent creep-rupture strength to 800 °C | Superior coal-ash and steam oxidation resistance | Good weldability with controlled PWHT | ASME Code Case 2702 approved
  • Certification:ISO 9001 and AS 9120B certified; full batch traceability; in-house laboratory verification.
  • Product Forms: Bar & Rod | Forgings & Rings | Seamless Pipe & Tube | Plate | Welding Wire

If you need a size, temper, heat-treatment condition or certification that is not listed below, send us the drawing — we will confirm mill capability and lead time within one working day.

II. Material Standards & Specifications

Standard / Specification

Product Form

Description

UNS N07740

–

Unified numbering system

ASTM B983 / ASME SB983

Bar, forgings, seamless tube

Precipitation-hardened Ni-Cr-Co alloy – current edition

ASME Code Case 2702

Sheet, plate, rod, seamless pipe & tube, fittings, forgings

A-USC boiler construction, Section I & B31.1 – max 800 °C

AWS A5.14 ERNiCrCoMo-1

Welding filler

Matching filler metal for 740H

EN 10204 3.1

Mill certificate

3.2 / third-party inspection available on request

Material must be supplied in the solution heat-treated and aged condition. ASME Code Case status and revisions should be confirmed with ASME before specification.

III. Chemical Composition (wt%)

Element

Min

Max

Nickel (Ni)

Balance

–

Chromium (Cr)

23.5

25.5

Cobalt (Co)

15.0

22.0

Niobium (Nb)

0.50

2.50

Titanium (Ti)

1.15

1.65

Aluminum (Al)

1.20

1.75

Molybdenum (Mo)

0.30

2.00

Carbon (C)

0.02

0.08

Manganese (Mn)

–

0.50

Silicon (Si)

–

1.00

Phosphorus (P)

–

0.030

Sulfur (S)

–

0.015

IV. Service Conditions & Material Selection Boundaries

Suitable Conditions

  • Advanced ultra-supercritical (A-USC) superheater and reheater tubing at 700–800 °C
  • Thick-section steam headers and main steam piping above 700 °C
  • Pressure-containing components exposed to coal-ash corrosion and high-temperature steam oxidation
  • Concentrated solar power receivers and high-temperature salt-loop tubing

Typical Applications

  • Power Generation: A-USC boiler tubes, steam headers, main steam piping, turbine components
  • Oil & Gas / Petrochemical: High-temperature pressure piping and heat exchangers
  • Concentrated Solar: Receiver and molten-salt loop components

Selection Boundaries

  • Below 700 °C / cost-sensitive service: consider Inconel 617 or Alloy 800H
  • Severe aqueous corrosion: consider Inconel 625 or Hastelloy C-276
  • Maximum strength at moderate temperature: consider Inconel 718

V. Manufacturing Process & Heat Treatment

Process

Parameters

Outcome

Solution Anneal

≥ 1100 °C (2010 °F), 1 hr per 25 mm thickness (min 0.5 hr), rapid cool

Dissolves γ′, recrystallizes

Aging

760–815 °C (1400–1500 °F), min 4 hr up to 50 mm thickness

γ′ precipitation, peak strength

Post-Weld Heat Treatment

760–815 °C (1400–1500 °F), mandatory per Code Case 2702

Restores properties in weld zone

Fabrication: Welding by GTAW / SAW with matching ERNiCrCoMo-1 filler; PWHT is mandatory; a weld strength reduction factor of 0.70 applies above 600 °C for longitudinal seams. Hot working at 1050–1150 °C. Cold forming above 5 % strain requires full solution + aging re-treatment of the entire component. Machining with rigid setups, positive feeds and sharp carbide tooling.

VI. Mechanical Properties

Condition: Solution Treated + Aged (Room Temperature)

Property

Typical / Minimum Value

Tensile Strength

≥ 1000 MPa (145 ksi)

Yield Strength (0.2 % offset)

≥ 620 MPa (90 ksi)

Elongation

≥ 20 %

Hardness

Contact for certified test reports

Elevated-Temperature Tensile (transverse, aged):

Temperature

Yield Strength

Tensile Strength

700 °C (1292 °F)

567 MPa (82.2 ksi)

861 MPa (124.9 ksi)

750 °C (1382 °F)

596 MPa (86.4 ksi)

818 MPa (118.6 ksi)

800 °C (1472 °F)

594 MPa (86.2 ksi)

691 MPa (100.2 ksi)

Design stress values (Su, Sy) per ASME Code Case 2702 Tables 5/5M and 6/6M. Certified test reports available on request.

VII. Material Comparison Guide

Dimension

Alloy 740H

Alloy 617

Alloy 625

Alloy 718

Primary Strength

Creep strength to 800 °C

Solid-solution strength

Corrosion + strength

Highest strength to 704 °C

Strengthening

Gamma-prime (γ′)

Solid-solution

Solid-solution

Gamma-double-prime (γ″)

Max Use Temperature

800 °C (code-approved)

~980 °C

~980 °C

~704 °C

Coal-Ash Corrosion

Excellent

Good

Moderate

Poor

Weldability

Good (with PWHT)

Excellent

Excellent

Excellent

Typical Use

A-USC boilers, steam piping

Gas turbines, chemical

Marine, chemical, FGD

Aerospace, oil & gas tools


 


Procurement Recommendation: ChooseInconel 740H for A-USC boiler and steam piping where code-approved creep strength and coal-ash corrosion resistance above 700 °C are required. Choose Alloy 617 for lower-cost high-temperature service without code qualification. Choose Alloy 625 for severe aqueous corrosion. Choose Alloy 718 for maximum room/moderate-temperature strength and easier fabrication.

Request a Quote or Sample Today

For A-USC power generation and high-temperature pressure applications demanding Inconel 740H performance, contact ZYTC Alloy today. Our technical team is ready to assist with material selection, heat treatment specification and code compliance.

Contact Us:  Email: daisy@zytcsteel.com  |  WhatsApp / WeChat: +86 17335753350

Tianjin ZYTC Alloy Technology Co., Ltd
 
 ZYTC Alloy CERTIFICATION
Inspection Equipment