+86-17335753350

Model No: UNS N09939 / 2.4635

Alloy 939 (UNS N09939) Investment-Cast Turbine Blades

Alloy 939 (UNS N09939) investment castings & AM-ready powder. High-Cr superalloy for turbine vanes, blades and hot-section parts to 850 C. Mill cert per lot.
Quantity :
Contact Now

Alloy 939 (UNS N09939 / W.Nr. 2.4635 / GB GH 939), formerly designated INCONEL® alloy 939 (IN 939), is a high-chromium, gamma-prime strengthened nickel superalloy developed in the early 1970s for cast hot-section components. It combines tensile, creep and thermal-fatigue strength at temperatures up to about 850 °C (1560 °F) with oxidation and hot-corrosion resistance that clearly outperforms 16%Cr cast superalloys in sulphur-bearing fuels.

Its strengthening system is dual: a high gamma-prime (γ′) volume fraction for precipitation hardening, and one of the highest chromium levels among cast superalloys for environmental resistance. That combination is exactly what industrial and marine gas turbines burning heavy fuel oil or low-calorific gas demand — and it is why Alloy 939 remains a standard material for vanes, blades and combustor hardware decades after its introduction.

ZYTC Alloy supplies Alloy 939 as investment castings, machined blanks and AM-ready powder, with vacuum induction melting, full heat treatment, complete traceability and certified test reports for every lot.

Quick Facts

Grade
Alloy 939 (IN 939)
UNS
N09939
W.Nr.
2.4635
GB
GH 939
Type
Precipitation-hardened, cast Ni superalloy
Service temp.
to ~850 °C / 1560 °F
Density
8.27 g/cm³
Melting range
~1230–1340 °C

Chemical Composition (typical, weight %)

ElementNiCrCoWTaNbTiAlZrCB
NominalBalance22.519.02.01.41.03.71.90.10.150.01

Si and Mn are controlled to low residuals (commonly ≤0.3 and ≤0.2 %); all trace elements are limited per the applicable purchase specification. Unlike many second-generation cast superalloys, Alloy 939 contains essentially no molybdenum — tungsten is the solid-solution strengthener. Nominal values above follow the published alloy definition; acceptance limits are those of the order specification or OEM process spec, not these nominal figures.

Physical Properties (typical)

PropertyValueImperial
Density8.27 g/cm³0.299 lb/in³
Melting range (approx.)1230–1340 °C2246–2444 °F
Elastic modulus, RT~190 GPa27.6 × 10⁶ psi
Thermal conductivity, 100 °C10.0 W/m·K—
Thermal expansion, 20–1000 °C13.7 μm/m·°C7.6 μin/in·°F
Specific heat, RT440 J/kg·K—
Electrical resistivity, 20 °C1.38 μΩ·m—

Values are typical literature and supplier data for the fully heat-treated condition; they vary with casting route and microstructure and are provided as a design guide only.

Mechanical Properties (cast + fully heat-treated, typical)

PropertyMetricImperial
Tensile strength, RT1000–1180 MPa145–171 ksi
Yield strength (0.2 %), RT700–850 MPa102–123 ksi
Elongation, RT5–8 %5–8 %
Hardness330–390 HB—
Stress-rupture capability≥140 MPa / 1000 h at 870 °C≥20 ksi / 1000 h at 1600 °F

Acceptance values are those stated in the purchase order and the applicable OEM process specification; request the certified test report for the actual lot. Hot-section castings are normally qualified by individual OEM specs rather than by a general-purpose bar/plate standard.

Heat Treatment

Alloy 939 reaches its design strength only after a full precipitation-hardening sequence; the as-cast (or as-built AM) structure is not the delivery condition. Representative cycles:

RouteStepCondition
Castings (representative)1. Solution~1160 °C (2120 °F), 4 h, air cool — homogenises the matrix and dissolves eutectic γ′
2. Primary age~1000–1080 °C (1832–1976 °F), 4 h, air cool
3. Secondary age~845 °C (1553 °F), 16–20 h, air cool — precipitates the fine γ′ that carries the strength
AM parts (LPBF-optimised, per EOS-type process spec)1. Solution1190 °C (2174 °F), 4 h, fast air/argon cool
2. Age 11000 °C (1832 °F), 6 h, fast cool
3. Age 2800 °C (1472 °F), 4 h

Exact schedules must follow the applicable process specification and component geometry. Solution treatment also dissolves undesirable phases that form during solidification. As-built LPBF material contains insufficient γ′; without the full sequence it will not reach design strength.

Alloy 939 vs Alloy 738LC — which one for your turbine?

CriterionAlloy 939Alloy 738LC
Chromium~22.5 %~16 %
Hot corrosion / sulphidation resistanceSignificantly betterModerate
Creep-rupture strength at temperatureComparableComparable
Cost / availabilitySlightly higherBase case, higher volume
Typical fuel environmentSulphur-bearing heavy fuel oil, low-grade gasClean natural gas

Rule of thumb: clean fuel → Alloy 738LC; corrosive, sulphur-rich fuel or marine environment → Alloy 939. The higher chromium also reduces the reliance on protective coatings, which lowers lifetime maintenance cost on industrial frames.

Applications

Industrial gas turbines
Nozzle guide vanes, rotor blades, heat shields, combustor hardware
Marine & microturbines
Salt-laden and sulphur-bearing fuel environments; turbocharger wheels
Additive manufacturing
LPBF / DED parts with complex internal cooling passages, retrofit vane repairs

Welding & Repair

Alloy 939 is repair-weldable with precautions: the high γ′ content makes it prone to microfissuring in the heat-affected zone. Successful repair of vane and blade castings requires preheat, low-energy welding parameters and a full post-weld heat treatment. New fabrication welds are limited; design castings so that critical joints are avoided or machined afterwards.

Specifications — read this before comparing quotations

Alloy 939 is not covered by a general-purpose AMS or ASTM bar/plate specification. Beware of datasheets quoting “AMS 5400” — that SAE number covers a 15Cr stainless investment casting, not this alloy. In practice Alloy 939 is procured against OEM process specifications (turbine-maker vane and blade specs), national designations (UNS N09939, W.Nr. 2.4635, GB GH 939) or, for additive manufacturing, against AM material specifications. We test to the specification called out on your drawing; if your drawing references an OEM spec number, send it with the RFQ.

 


Why ZYTC Alloy

  • Vacuum induction melting with full melt traceability, certified test report with every lot
  • Investment casting to drawing plus machining of critical seal and bearing faces
  • AM-ready Alloy 939 powder with controlled particle-size distribution (typ. 15–53 μm / 20–55 μm)
  • Full heat-treatment service so parts arrive in the final qualified condition
  • Engineering support on heat-treatment schedules and repair-weld planning before you commit to a drawing

Send us your drawing or application description — we will confirm feasibility, quote the most economic route (cast vs AM) and give a lead time within one working day.

INCONEL® is a registered trademark of Special Metals Corporation, a PCC company. Alloy 939 and IN 939 are used here for grade identification only.

Tianjin ZYTC Alloy Technology Co., Ltd
 
 ZYTC Alloy CERTIFICATION
Inspection Equipment