3 Benefits of Stainless Steel for Medical Applications

Medical Stainless Steel Selection: 316L, 440C, and 316LVM Are Not Interchangeable
For surgical instrument, implant, and medical equipment design engineers and buyers — supplied by ZYTC Alloy, ISO 9001 certified manufacturer and exporter
“Medical Stainless Steel” Is a Phrase That Causes Procurement Errors
Open any materials supplier’s website and you will see similar language: “Stainless steel resists corrosion, is easy to sterilize, and is non-magnetic, so it is widely used in medical applications.” Those statements are not wrong, but they lump together 316L surgical instrument handles, 440C scalpel blades, and 316LVM bone screws under a single “medical stainless steel” label.
These three materials have completely different application scenarios, procurement standards, and failure risks. Treating them as interchangeable is the most common source of error in medical stainless steel procurement. The table below puts the three side by side.
At a Glance: Three Grades, Three Different Jobs
| Item | 316L | 440C | 316LVM |
|---|---|---|---|
| UNS designation | S31603 | S44004 | S31673 |
| Microstructure | Austenitic | Martensitic | Austenitic (vacuum remelted) |
| Typical hardness | Low (annealed) | High after hardening | Low to medium (cold worked) |
| Corrosion resistance | Good | Moderate | Excellent |
| Primary medical use | Instrument handles, trays, equipment | Scalpel blades, scissors, dental burs | Bone screws, plates, short-term implants |
| Governing standard | ASTM A276 / A479 | ASTM F899 (chemistry reference) | ASTM F138 |
| Key procurement variable | Passivation and surface quality | Hardness and tempering condition | Vacuum melting and inclusion control |
316L: The Right Choice for Non-Implant Instruments — But Not “Universal Medical Steel”
316L (UNS S31603) contains 2–3% molybdenum, giving it better pitting and crevice corrosion resistance in chloride environments than 304. Its low-carbon design (≤0.030%) reduces the risk of weld sensitization . It is widely used for instrument handles, instrument trays, equipment structures, and fluid lines.
What procurement must specify: 316L's “medical” positioning is non-implant. If the instrument undergoes repeated autoclave sterilization or exposure to chlorine-based disinfectants, 316L is a reasonable choice — but the passivation state (per ASTM A967) and incoming surface quality (no grinding burn, no embedded iron contamination) determine actual corrosion performance more than the grade name itself. A certificate will not reflect these.
Research confirms that surface treatment matters: in fatigue testing under simulated in vivo conditions, 316L (annealed) showed significant surface pitting and damage, while 316LVM showed almost none . For 316L, passivation and surface finish are not cosmetic — they are functional requirements.
440C: Blades and Scissors Need Hardness, Not Corrosion Resistance
440C is a high-carbon martensitic stainless steel with carbon content of 0.95–1.20% and chromium of 16–18% . After heat treatment it can reach HRC 58–60, making it suitable for scalpel blades, scissors, dental burs, and other edge-wear-dominated instruments. Its corrosion resistance is lower than 316L, but in these applications edge retention matters more than corrosion resistance — blades are single-use or short-term, and do not serve long-term inside the body.
Technical data (ASTM F899 reference values):
| Property | 440C typical value |
|---|---|
| Carbon | 0.95 – 1.20% |
| Chromium | 16.0 – 18.0% |
| Hardness after hardening (204°C temper) | ~59 HRC |
| Hardness after hardening (260°C temper) | ~57 HRC |
| Tensile strength (hardened) | up to ~2030 MPa |
| Elongation (hardened) | 4% |
Data compiled from AMS 5630 and ASTM F899 reference tables .
What procurement must specify: 440C’s carbon content and heat treatment determine final hardness and toughness. If the supplier provides only “440C” without the heat treatment condition and measured hardness, you cannot judge whether the blade will chip or roll. For scalpel blades, require the certificate to report measured HRC rather than accepting “conforms to standard.” Note also that ASTM F899 itself states: mechanical property requirements, heat treating requirements, and hardness requirements are governed by the appropriate material standard or by agreement between purchaser and supplier — the F899 chemistry reference alone is not a purchase specification for hardness .
316LVM: The Starting Point for Implants — Not an “Upgraded 316L”
316LVM (UNS S31673) is the high-purity version of 316L, produced by vacuum remelting to reduce inclusions and interstitial elements. It is used for bone screws, bone plates, and short-term implants. Its “medical grade” status comes from melting practice and inclusion control, not from a dramatically different chemistry.
Technical data (ASTM F138, annealed bar/wire):
| Property | 316LVM (annealed) | 316L (annealed, for comparison) |
|---|---|---|
| Carbon | ≤0.025% | ≤0.030% |
| Chromium | ~17.5% | 16.0 – 18.0% |
| Nickel | ~14% | 10.0 – 14.0% |
| Molybdenum | ~2.8% | 2.0 – 3.0% |
| Sulfur | ≤0.003% | ≤0.03% |
| Tensile strength (min) | 490 MPa | ~485 MPa |
| Yield strength (min) | 190 MPa | ~170 MPa |
| Elongation | 45% | 40% |
316LVM values per Alleima/Sandvik datasheets (ASTM F138) . 316L values per ASTM A276 reference .
The key difference is not the minimum mechanical values — it is the sulfur and inclusion control. Lower sulfur and vacuum melting reduce inclusion-initiated fatigue and corrosion. Research confirms that 316LVM (cold worked) outperforms 316L (annealed) in fatigue performance in both dry and wet corrosive environments .
What procurement must specify: 316LVM’s purchase standard is typically ASTM F138 (wrought 316L stainless steel for surgical implants), not the ordinary 316L standards ASTM A276 or A479. If the drawing says “316LVM” but the PO does not reference F138, the supplier may deliver to ordinary 316L inspection standards — and inclusion level and grain size control may not meet implant requirements. This is the single most important alignment point in implant procurement.
A Practical Procurement Decision Table
| Application | Recommended grade | Procurement key points |
|---|---|---|
| Instrument handles, trays, equipment structures | 316L | Passivation state, surface quality, non-implant positioning |
| Scalpel blades, scissors, dental burs | 440C | Heat treatment condition, measured HRC, edge toughness |
| Bone screws, plates, short-term implants | 316LVM (ASTM F138) | Vacuum melting, inclusion control, cite F138 not ordinary 316L |
| Long-term implants (stents, etc.) | Cobalt-chromium alloys (e.g., L605 / MP35N) | 316LVM is not intended for long-term implant service |
ZYTC Alloy's Supply Positioning
ZYTC Alloy supplies medical-grade stainless steel, nickel alloys, and cobalt alloys, covering 316L and 440C for non-implant instruments and 316LVM to ASTM F138 for implant applications. We do not treat “medical stainless steel” as a single selling point — grade, standard, condition, and inspection requirements must align with the application.
Please provide in your inquiry: application (non-implant instrument / short-term implant / long-term implant), grade, governing standard, condition requirements (e.g., 440C heat treatment hardness, 316LVM F138 reference), and quantity.
📧 daisy@zytcsteel.com
📲 WhatsApp / WeChat: +86 17335753350
Kovar Alloy: Precision Engineered for High-Performance Machining Applications
Applications of High-Temperature Alloys in the Medical Industry
Related Article